Excalibur 366 Spezifikationen Seite 124
- Seite / 254
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Excalibur Multirate DAP Installation and Operation
5-36
Local Alarm Display
This parameter specifies whether the front panel displays alarms that occur at the local
DAP. (Incoming alarms are always displayed when the unit is configured for RCP
control.) When disabled, local alarms are not displayed on the front panel, but may be
reported to the CMS network management system.
Analog Regeneration
This parameter specifies whether the DAP's analog receiver regenerates secondary
channel signals through the digital transmitter. The normal setting for most networks is
Enabled.
Digital Regeneration
This parameter specifies whether the DAP's digital receiver regenerates secondary
channel signals through the analog transmitter. The normal setting for most networks is
Enabled.
Diagnostic Compatibility
This parameter specifies whether enhanced diagnostics are available. Since older DAPs
do not perform the new diagnostics, the Diagnostic Compatibility parameter simplifies
diagnostic testing by deleting the new diagnostics from the front panel menus. If you are
performing tests with Multiport or Multirate DAPs equipped with Software Revision No.
SSC0778 or lower, select On. To determine the software revision number of the unit,
enter the Status submenu, press the button beneath Unit, then press the button beneath
Revsn.
Route Secondary Channel
This parameter appears on the screen only for units equipped with the Analog or ISDN
IDBU feature. It specifies whether the secondary channel transmits data across the dial-
up telephone line, while the primary channel transmits data over the digital lines. When
the To Dial option is selected, you can establish a dial backup connection with a remote
Excalibur DAP and perform diagnostics and/or monitoring operations without affecting
primary channel data on the dedicated line. This option provides a remote DAP
operating in DDS or CC64 mode with a non-interruptive secondary channel and provides
a CMS network management system with T7 secondary channel connection to a remote
DAP.
- Excalibur 1
- Multirate DAP 1
- Warranty 2
- Milgo Solutions 3
- Customer Information Contacts 3
- About This Manual 5
- Terminology and Conventions 6
- Table of Contents 7
- Chapter 6 - On-Line Operation 11
- Chapter 7 - Troubleshooting 11
- Important Safety Instructions 15
- Excalibur Multirate DAP 16
- Chapter 1 17
- Introduction 17
- Standalone Model 20
- Central Site Model 21
- Standard Features 22
- Password Protection 23
- RTS-DCD Simulation 23
- Extended Range Operation 23
- Rate Adaption 23
- Built-In Diagnostic Tests 23
- Alarm Reporting 24
- Line Parameter Monitoring 24
- Call Messages 24
- CMS DSU Compatibility 25
- Multiport Frame Compatibility 25
- CMS Compatibility 25
- Backward Compatibility 26
- Dual Interface 27
- Integral Dial Backup 27
- Model for EDRS 29
- Chapter 2 31
- Operating Modes 31
- Primary Channel Interface 32
- Network Management Controller 32
- Main Channel Interruption 33
- Clear Channel 64 Kbps) 34
- Clear Channel 64 Kbps 35
- Clear Secondary Channel 35
- Antistreaming 36
- Call Establishment 38
- Call Answering 38
- Call Disconnection 39
- ISDN Integral Dial Operation 42
- Chapter 3 47
- Installing the DAP 47
- Cable Connections 48
- TO TELCO JACK FOR 55
- ANALOG IDBU OR TO 55
- ISDN BASIC RATE 55
- U-INTERFACE FOR 55
- ISDN IDBU 55
- TO TELCO JACK 57
- DMM Connector 61
- Setting the Jumpers 62
- Digital Bridge Board 68
- Connectors 70
- AC Power Connection 71
- Calibration 72
- Chapter 4 73
- Using the Front Panel 73
- What You Will See First 74
- Moving Through the Menus 74
- Status Display 76
- Entering Unit Addresses 77
- 79
- Entering the Password 80
- Changing the Password 81
- Locking Front Panel Functions 82
- Establishing a Security Code 83
- Front Panel Test 85
- Auto-Learn Network 86
- Event Displays 87
- Chapter 5 89
- Defining Operating Parameters 89
- R a t e M P F r m 91
- DAP Parameters 96
- Location 99
- Transmit Clock 100
- Port Receive Clock 100
- CTS Delay 101
- Squelch Primary Transmitter 101
- EIA Pin 21 102
- EIA Pin 18 102
- Remote Digital Loop 102
- DTR Control 103
- CTS Control 103
- RTS Simulation 103
- DCD Simulation 103
- Protocol 106
- Interface 106
- Latching Loopback 107
- Transmit Calibrate 107
- Secondary Channel 107
- Network Delay 108
- Automatic Poll 109
- Channel Parameters 110
- Escape Top 111
- Channel Assignment 114
- Naming Channels 115
- Port Rate Configuration 118
- RCP Parameters 120
- Controller 122
- RTS Mode 122
- DCD Mode 122
- Secondary Channel Format 122
- Local Diagnostics 123
- Remote Diagnostics 123
- Alarm Detection 123
- Local Alarm Display 124
- Analog Regeneration 124
- Digital Regeneration 124
- Diagnostic Compatibility 124
- Route Secondary Channel 124
- Analog Dial Parameters 126
- Dial Mode 127
- Wait to Dial 129
- Call Progress 129
- Automatic Dial 129
- Automatic Dial Timer 129
- Switch to Dial 130
- Automatic Disconnect 130
- Retry Attempts 130
- Dedicated Line Test 130
- Line Test Interval 130
- DCD Threshold 131
- Switched 56 Dial Parameters 132
- Port RTS-DCD Simulation 137
- Ring Detect 137
- ISDN Dial Parameters 138
- Switch Type 139
- Parameter Thresholds 142
- User LED 144
- Alias Parameter 145
- System Submenu 147
- Chapter 6 149
- On-Line Operation 149
- Line Quality Statistics 159
- N e x t P r e v 166
- ISDN Dial Backup Alarms 170
- Viewing Stored Alarms 171
- Dial Backup Procedures 173
- Entering Telephone Numbers 174
- P r i m a r y P h # = 175
- Originating Dial Backup Calls 179
- Analog Dial Line Tests 180
- Switched 56 Dial Line Tests 184
- ISDN Dial Line Tests 185
- Activating the Tests 186
- Activating Timed Tests 187
- Activating Loop Tests 188
- Sending Call Messages 189
- Chapter 7 193
- Troubleshooting 193
- Self-Error Test 194
- Local-Error Test 195
- End-to-End Error Test 196
- Network-Error Test 197
- DDS Loop Test 198
- Digital Loop Test 198
- V.54 Digital Loop Test 199
- Loop 2 and Loop 2 Error Tests 200
- Service Loops 201
- Individual Port Testing 206
- Channel Testing 207
- RTN Function 208
- Isolating Network Problems 209
- Appendix A 213
- Technical Specifications 213
- Operating Range 214
- Environmental 214
- Analog IDBU Option 215
- Appendix B 217
- Appendix C 219
- Status Notes 220
- Configuration - DAP Notes 222
- Configuration - DAP 223
- Continued 223
- Excalibur DAP 227
- Assignment, User, System 235
- Diagnostics Notes 236
- Diagnostics 237
- Dial, Call, Security 239
- Address, Service, RTN, ALNet 241
- Appendix D 243
- Regulatory Information 243
- TWFM-004 - Rev B.0 7/1/95 253
- BUSINESS REPL Y MAIL 254
Verwandte Produkte und Handbücher für Nein Excalibur 366
Nein Excalibur 414PE-BK Betriebsanweisung
(11 Seiten)
(11 Seiten)
Nein Excalibur 415-SE Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Nein Excalibur Samurai Bedienungsanleitung
(6 Seiten)
(6 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern